US丨4 Axis USB Mach3 CNC Controller Kit Nema23 Stepper Motor 76mm 270oz-in&Driver

Description: US丨4 Axis USB Mach3 CNC Controller Kit Nema23 Stepper Motor 76mm 270oz-in&Driverfor CNC Router Engraving Milling Machine Good News: We have USA Warehouse in USA,so we will ship this product from USA to you Parcel include:4× 23HS8430 Nema23 stepper motor 76mm 70oz-in 3A4× TB6600 stepper motor driver1× 4 Axis USB Mach3 control board1× USB Cable1× 350W 24V DC switching power supply1× CD disc 4 Axis Nema23 Stepper Motor Driver USB Mach3 Board Power Supply CNC Controller Kit Nema23 Stepper motor 76mm/270Oz-in/ 3A 1.8Nm General Specification: Step angle accuracy: ±5%(full step,not load)Resistance accuracy: ±10%Inductance accuracy: ±20%Temperature rise: 80deg Max(rated current,2 phase on)Ambient temperature ----------—20deg ~+50degInsulation resistance:100MΩ Min,500VDCInsultion Strength--------500VAC for one minute Wiring: A+ : RedA- : GreenB+ : YellowB- : BlueTB6600 stepper motor driver 4.5A Parameters: The working voltage is DC 10V-45V. It is recommended to use switching power supply DC32V for power supply.Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560.The rated maximum output reaches: ±4.5A.Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A.Automatic half-flow function.Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions. Description: The working voltage is DC 10-45V; it is recommended to use DV32V switching power supply.There are two input terminals, both of which adopt the common anode input mode.The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required.The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked.The motor rotates forward when CW is high or suspended, and reverses when it is low.When EN is high or floating, it is working state, when it is low, it is offline. Note: The power supply cannot be connected reversely, otherwise the chip will be burnt out.The set current should not exceed the rated current of the motor. Terminal & Subdivision settings:Wiring diagramsFeatures:1. Support for 4-axis linkage, you can connect four stepper motor drives or servo drives;2. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;3. 4 general-purpose opto-couplers isolation input : can connect the limit switch, emergency stopswitch, auto tool zero, home switch etc.4. Support for connecting electronic handwheel;5. Have 0-10V signal output , you can use mach3 software to control the spindle motor speed.6. 4 general-purpose isolated relay drive output interface, can drive four relays for controllingthe spindle starts, forward rotating and reverse rotating, pumps or other device;7. 1 status LED, indicate connection status on the boardMach3 USB Motion Card STB4100 V2.11.2.Software license application:Copy license files “Mach1Lic.dat” from “mach3 software folder”,to C:\Mach3 Cover theoriginal file,Reset Computer（must reset the computr,please don't open the software dircetly!）Way above the license for DIY or study purposes only, not for commercial use.1.3. Installation the software of the USB motion card:This USB motion card does not need install any USB driver,Windows2000/XP/Windows7/8/10,candirectly identify.1.3.1 Connecting the USB cable to the PC and the motion card:The first installation of motion control card, take about 10s, when the green led lights on motioncontrol card, indicating that the connection is successful, return the following tips when youinstall on your computer 350W 24V DC switching power supplyDC output: 24V 0-14.5ADC voltage of Adjustable range: ±10%AC input voltage range: 115VAC/6.5A/50HZ or 230VAC/3.4A/60HZ; Selected by switchOverload protection: 105%-135% cut off the output, automatic recoveryOver-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recoverWorking Temperature: -10℃～+50℃ Shipping Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately Items will be shipped within 1-2 days upon the receipt of payment. Problem&Feedback Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it. We are a new member in ebay now, and need understand both of sides Pls email us before you want to leave any negative feedback Refund When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost Contact us Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s email within 1-2 business days,if not pls check the mail box again Customer’s satisfaction is very important to us.

Price: 135 USD

Location: New York

End Time: 2024-07-20T07:32:28.000Z

Shipping Cost: 0 USD