ELEKIT TU-8200R 6L6GC Single Vacuum Tube Amplifier Kit w/tracking New

Description: ELEKIT TU-8200R 6L6GC Single Vacuum Tube Amplifier Kit w/tracking NewDescriptionBrand New.Product SummaryThis is a single-operation power amplifier kit that uses a 6L6GC output tube with powerful and natural sound quality. The output tube can be replaced with a similar tube, and is automatically set to the optimal bias for the output tube being inserted. In addition, you can easily switch the operation mode of the output tube, allowing you to fully enjoy the fun of a vacuum tube amp with this one unit. ■Equipped with our proprietary "active auto bias adjustment function"In addition to the included output tube 6L6GC, KT66, KT88, 6550, EL34 (6CA7), etc. can be replaced.Normally, in order to bring out the full potential of the installed vacuum tubes, it would be necessary to adjust the bias for each vacuum tube each time, but with the TU-8200, the bias is automatically adjusted to the optimal bias condition for the installed vacuum tubes. Equipped with a unique function "active auto bias adjustment function" that adjusts the bias. This allows you to easily and easily enjoy the sound that brings out the full potential of vacuum tubes. ■Easily switch between 3 types of connection methodsPowerful "pentode connection", "triode connection" characterized by delicate sound, and "ultra-linear (UL) connection" which has the best of both worlds.These three types of output tube operation modes can be operated using short plugs. It's easy to do just by replacing it. ■A conductive polymer hybrid aluminum electrolytic capacitor with low ESR is used as the cathode bypass capacitor in the voltage amplification stage.This achieves high resolution and clear sound. ■Equipped with independent left and right FET ripple filtersThe B power supply is equipped with independent left and right FET ripple filters cultivated in successive TU series. Combined with the DC lighting of the voltage tube, hum noise is kept to a minimum. In addition, it is equipped with an overcurrent protection circuit in case of trouble with the output tube. ■Equipped with headphone terminalThe output level can be switched to 3 levels by replacing the jumper on the board according to the sensitivity of the earphones or headphones. ■Uses a glass epoxy board with 70μm copper foil, which is thicker than normal and has low conduction loss and high heat dissipation effect. ■Most of the circuit section is mounted on the board. Wiring to the outside of the board is also done using a connector, making this kit easy to assemble even for soldering beginners. [Precautions for use]**About using KT120 with TU-8200R**The KT120 can be used with upwardly compatible bulbs such as the KT88, but the heater current will be 25% higher than that of the KT88, and there will be no margin for power supply capacity, so avoid using it continuously for long periods of time to avoid trouble. please. (Especially during high temperatures in summer) Product Specifications・Circuit configuration:Vacuum tube single operation stereo power amplifier (all stages of the signal system are vacuum tube configuration)All stages of the signal system are vacuum tube type.Output tube operation mode can be switched with jumper plug:　　　　UL (Ultra Linear) connection, pentode connection, triode connectionEquipped with active auto bias circuitEquipped with MOSFET type B power supply ripple filter (left and right independent)Equipped with output tube overcurrent protection circuit (left and right independent) ・Vacuum tubes used:[Output tube] 6L6GC x 2, [Voltage amplification tube] ECC82 (12AU7) x 2*EL34 (6AC7), KT88 and equivalent output tubes can also be used. ·Rated output:8W + 8W (using 6L6GC, UL connection),8.2W + 8.2W (using 6L6GC, with pentode connection),4W + 4W (using 6L6GC, with triode connection)*All with 8Ω load ・Rated input: 230mV (when using 6L6GC and UL connection) ・Residual noise: 90μV (IEC-A)・Frequency characteristics: 12Hz to 70kHz (-3dB)・Compatible speaker: 4 to 16 Ω (switch between 4 to 6.3 Ω and 8 to 16 Ω ranges with a switch)・Compatible headphones: 8Ω to 1kΩ (high impedance compatible, unbalanced)Output level can be changed to 3 levels according to headphone sensitivity・Output terminal: Speaker output: Gold-plated binding terminal (banana plugs can be used)Headphone output: 3-pole standard (φ6.4mm) jack・Line input terminal:RCA jack stereo 2 systems (INPUT1, INPUT2)3-pole mini (φ3.5mm) jack 1 system (INPUT2 side, 3-pole mini jack priority)・Power supply voltage: AC100V 50/60Hz (IEC standard 3P inlet type)・Power consumption: 60W (when using 6L6GC), 85W (when replacing with KT88)・Body dimensions: W252 x H175 x D285mm (including protrusions when attached vacuum tube is installed)・Body weight: Approximately 6.6kg (excluding power cord)ShippingWe use Japan Post, Fedex or DHL for transportation.We will ship within 10 business days after payment is confirmed.It takes about 5~10 days from shipping to delivery.Shipping is free (included in the item price).For some shipments to Canada, Australia, New Zealand, please note that additional shipping fee may occur due to remote areas specified by carriers.International Buyers - Please Note:Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility. Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges. We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. Thank you for your understanding.

Price: 658.99 USD

Location: Hamamatsu,Shizuoka

End Time: 2024-09-16T04:33:04.000Z

Shipping Cost: 0 USD