Electronic Ignition Conversion Kit for 6-Cyl Autolite/Prestolite Dist

Description: Electronic Ignition Conversion Kits for 6-Cylinder Autolite/Prestolite Distributors Electronic Ignition Conversion Kit fits Certain 6-cylinder, non-vacuum-advance Autolite Distributors with Clip-Down Distributor Cap and breaker plate with two vertical screws Replaces Entire Breaker Plate - Simple to Install. The Hot-Spark electronic ignition conversion kit replaces breaker points and condenser in the distributor to provide rock-solid reliability. With the Hot-Spark electronic ignition, dwell and timing are always spot-on accurate. No matter how strong your engine is, you won't get the most out of it without a good spark. The stock points-based ignition system used technology that dates back a century - to the Kettering system, which was introduced in the 1910 Cadillac. Even though you can adjust breaker points for near-electronic ignition performance, they will burn and wear within a few thousand miles, long before the recommended replacement interval. With points, the timing will drift; power and fuel economy will suffer. The Hot-Spark electronic ignition conversion kit delivers a strong spark every time and is maintenance-free. You'll notice quicker starts, more top end power and a little gas mileage boost. It's as easy to install as points and condenser! Advantages of the Hot-Spark electronic ignition conversion kit: Replaces points and condenser with solid-state electronics Set it and forget it - Never adjust points and timing again! Zero maintenance Delivers far more voltage to the spark plugs than points-based points Reliable Hall-effect technology Never gets out of adjustment Rock-steady reliability Dwell and timing are always spot-on accurate Increased gas mileage, fuel economy Quick starting Smooth idling Cleaner emissions Longer spark plug life Longer engine life Cleaner engine oil due to less unburned fuel Longer interval between oil changes Easy to install - If you can install points, you can install the Hot-Spark electronic ignition conversion No points to wear, burn, pit or corrode No condenser needed Absolutely no points float - zero - even at redline RPM and beyond! Never worry about drifting dwell or timing again No rubbing parts - nothing to wear out! Fits completely under the distributor cap Stealth modification - maintains stock appearance Includes everything you need, no external ignition box required. Works with stock distributor and coil Encased in high-temp thermoplastic - protected from the elements and oil, grease, dirt, water, etc. Never bother with points or condenser again! The best investment you'll ever make for your vehicle Saves precious ($$$) fuel Coil with 3.0 Ohms or more internal, primary resistance required. Bosch Black Coil is ideal for 4- and 6-cyl Hot Spark ignition kits. Requires a 12-volt, negative ground electrical system. External Ballast Resistor: If the charging system voltage, measured at the coil's + terminal, is more than 13.9 volts at any RPM level, the voltage regulator likely needs replacing or a 1.4 Ohm ballast resistor should be wired between the coil's + terminal and the red HotSpark ignition wire. Too much voltage can damage the ignition module and other electronic components. How many miles until the Hot-Spark electronic ignition conversion kit pays for itself? Click here Measuring Coil Resistance (and more): www.Hot-Spark.com/Coil.htm 3AUT6U1 - For 6-cylinder Autolite/Prestolite non-vacuum-advance distributor with two vertical screws securing breaker plate to distributor body. The 3AUT6U1 Ignition Kit Fits ONLY These Autolite/Prestolite Non-Vacuum-Advance Distributors: IAD-4005A IAD-4012A IAD-4025 IAD-4025A IAD-4027 IAD-4033 IAD-4033A IAD-4034 IAD-4039-1 IAD-4040-1 IAD-4105-1M IAD-4108-1M IAD-411 4M IAD-4113M IAD-4114 1M IAD-4201 IAD-4201-1 IAD-4203-1 IAD-6001 IAD-6001-1B IAD-6001-2D IAD-6001-2F IAD-6001-2RL IAD-6001C IAD-6001D IAD-6001E IAD-6001G IAD-6002 IAD-6002-1A IAD-6002-1C IAD-6002-1D IAD-6002-1E IAD-6002-1F IAD-6002-1G IAD-6002-1K IAD-6006-1 IAD-6009-2A IAD-6010-1 IAD-SERIES IAO-4101-1M IAO-4103 IAO-4103-1 IAO-4103A IAO-4109-1M IAO-4112M IAO-4113-1M IAO-4113M IAO-4115-1M IAO-4116-1 IGC-4225F IGC-6001 IGC-6001-2D IGC-6001A IGC-6001B IGC-6001C IGC-6001G IGC-SERIES If your distributor part number (located on the side of the distributor body) is not listed here, this ignition kit WON'T FIT your distributor, even if your distributor KIND OF looks like the ones in the photos. If you order this part for a distributor not listed above, a 25% restocking fee will apply to your returned ignition kit, and only if it is in perfect, like-new condition. Note: This ignition kit's magnet sleeve WILL NOT fit ODD-FIRE distributors. The lobes of the distributor shaft must be evenly spaced. 3AUT6U1 Industrial Engine Applications Allis Chalmers 1957-58 6-Cyl 6B-230, 6B-273 IAD-6001-1B Autolite - 3AUT6U1 Autocar 1947-53 6-Cyl All models IAD Series Autolite - 3AUT6U1 Baker 1960-62 6-Cyl Type Me-1A Towing Tractor with Chrysler engine IAD-4039-1 Autolite - 3AUT6U1 Bay City (Crane) 6-Cyl 15, 15A; 25, 30, 37, 45, T185, T50, T150, T180, T450 IAD, IGC Series Autolite - 3AUT6U1 Brockway 1950-71 6-Cyl All models IAD, IGC Series Autolite/Prestolite - 3AUT6U1 Buda 1950-72 6-Cyl 6B-190, 205, 221, 225, 230 IAD-6001-1B Autolite/Prestolite - 3AUT6U1 1950-73 6-Cyl K-325, 369, 393, 428; L-468, 525; Lo-525 IGC-6001 Autolite/Prestolite - 3AUT6U1 1950-73 6-Cyl H-260, 298; HP-260, 298, 326, 351 IGC-6001 Autolite - 3AUT6U1 1953-54 6-Cyl FT-60, 75; HA, HB, JG IAD-6001-1B Autolite/Prestolite - 3AUT6U1 Chicago Pneumatic Tool Company 1955-65 6-Cyl 210RG-2 IAD-6001E Autolite/Prestolite - 3AUT6U1 1961-73 6-Cyl 85RJ-1 IAD-6001E Autolite/Prestolite - 3AUT6U1 Chrysler 6-Cyl 5A, 6A, 7A, 8A, 13, 13A, 14A, 15A, 16A, 22A IAD, IAO Series Autolite - 3AUT6U1 6-Cyl 32, 33, 908A, 931 IAD, IAO Series Autolite - 3AUT6U1 Clark 1956-66 6-Cyl All models IAD-6001D Autolite/Prestolite - 3AUT6U1 Continental 6-Cyl M engine21, IAD-6002 Autolite - 3AUT6U1 6-Cyl B, E engines IAD-6002 Autolite - 3AUT6U1 6-Cyl R, S, T, U engine IAD Series Autolite - 3AUT6U1 6-Cyl K engine IAD Series Autolite - 3AUT6U1 6-Cyl F6 engine 21, IAD Series Autolite - 3AUT6U1 Duplex 6-Cyl Shovel Chassis, Wagon Crane, (B-6427, F6244 engine) IAD-6002-1F Autolite - 3AUT6U1 Eaton, Towne, Yale 1955-60 6-Cyl All models IAD-4039-1 Autolite - 3AUT6U1 6-Cyl Chrysler engine IAD-4039-1 Autolite - 3AUT6U1 Galion Iron Works 6-Cyl 5-8 Ton Roller21, IAD-6002-1F Autolite - 3AUT6U1 Gambles Farmcrest 6-Cyl 40 IAD-6001-1B Autolite - 3AUT6U1 Harris 6-Cyl PH-43, PH-53 (5A, 8A engine) IAD-4039, 40 Autolite - 3AUT6U1 6-Cyl SPH-88, F6WC, F8, F8WC IAD Series Autolite - 3AUT6U1 Hi-Dynamic All 6-Cyl HF-HM (4WD Shovel), HMG, HR, HV IAD-6001 Autolite - 3AUT6U1 Jaeger All 6-Cyl 105, 125, 125A, 125B, 150, 160, 185, 250 “Air Plus” IAD-series Autolite - 3AUT6U1 All 6-Cyl 315, 3HM, 4 1/2 HM Mixers29, IAD-series Autolite - 3AUT6U1 Lincoln Welders 1962-66 6-Cyl Hercules JXD, QXLD-5 engine IGC-6001-2D Autolite/Prestolite - 3AUT6U1 Michigan All 6-Cyl C16, C24, T6K, T64, T66, TLDT-20, TMDT-16, -20 Autolite - 3AUT6U1 Minneapolis-Moline 1950-66 6-Cyl D, L Chrysler 30 engine IAD-4039-1 Autolite/Prestolite - 3AUT6U1 1974-78 6-Cyl G-1400, 1600 (Hercules gas engine) IAD-6013 Prestolite - 3AUT6U1 Mobilift All 6-Cyl D, L (Chrysler 30 engine) IAD-4039-1 Autolite - 3AUT6U1 Onan All 6-Cyl 15K, 25HN (5A, 6A engine) IAD-4039-1 Autolite - 3AUT6U1 Ready Power All 6-Cyl F, L2, L3, V IAD-6002-1G Autolite - 3AUT6U1 All 6-Cyl 1959 IAD-6002-1G Autolite - 3AUT6U1 Ross Carrier All 6-Cyl Series 12T, Y200 Lift Truck, Series 80, 90, 100 Carrier IAD Series Autolite - 3AUT6U1 Seaman And Wall All 6-Cyl GS7C IAD-6002-1A Autolite - 3AUT6U1 US Motors All 6-Cyl All models IAD-6002-1A Autolite - 3AUT6U1 Worthington All 6-Cyl 150, 160, 210 (F6-226, M-330, B6-427 engine) IAD-4027, 6002 Autolite - 3AUT6U1 Agricultural Engine Applications Case All 6-Cyl 600, 600G, 800G (Continental F209; H227 engine) IAD-6002-1G Autolite - 3AUT6U1 All 6-Cyl 900 (gas and LPG engine) IAD-6010-1 Autolite - 3AUT6U1 Cockshutt All 6-Cyl SP-109, 110, 112, 115, 132, 137, 215, 420 IAD-4040-1 Autolite - 3AUT6U1 All 6-Cyl 427, 28, 29; 430, 431, 525, 535, 542, 545 IAD-4040-1 Autolite - 3AUT6U1 All 6-Cyl 40 (Chrysler T- 120, 8A engine) IAD-4203-1 Autolite - 3AUT6U1 Custom All 6-Cyl B, C, E, ER, EW, HR, HW IAD Series Autolite - 3AUT6U1 Fox River 1958-59 6-Cyl Forage Harvester IAD-6002-1G Autolite - 3AUT6U1 Gehl (Forage Harvester) All 6-Cyl Continental FA-244, M-363 engine IAD-6002- Autolite - 3AUT6U1 International Harvester All 6-Cyl 80 Wisconsin VH4 engine Autolite - 3AUT6U1 All 6-Cyl 140 Wisconsin VR4D engine IAD series Autolite - 3AUT6U1 John Bean 1958-63 6-Cyl 40RC IAD-4040-1 Autolite - 3AUT6U1 All 6-Cyl 300G Rotomist Chrysler 32 engine Autolite - 3AUT6U1 John Deere All 6-Cyl 55 IAD-4012A Autolite - 3AUT6U1 All 6-Cyl 800 Chrysler 225 engine Autolite - 3AUT6U1 Jumbo All 6-Cyl B, C, E, ER, EW, HR, HW IAD series Autolite - 3AUT6U1 Love All 6-Cyl CF1, CF51, (Chrysler 5A, 6A engine) IAD-4039, 4201 Autolite - 3AUT6U1 Lundell All 6-Cyl 55-17 Continental F224 engine IAD-6002-1G Autolite - 3AUT6U1 Massey Ferguson All 6-Cyl Combine (Chrysler 5, 5A, 30, 251 engine) IAD-4039-1 Autolite - 3AUT6U1 All 6-Cyl 27 (Chrysler 8A, 30, 251, 265 engine) IAD-4040-1 Autolite - 3AUT6U1 All 6-Cyl 60SP, 70, 72SP, 80SP, 82SP, (Chrysler 5, 30, 251 engine) IAD-4039-1 Autolite - 3AUT6U1 All 6-Cyl 90SP, 92 (Chrysler 8A, 30, 251, 265 engine) IAD-4040-1 Autolite - 3AUT6U1 All 6-Cyl Clipper Forager Continental F-226 engine Autolite - 3AUT6U1 All 6-Cyl 44-6 Continental F-226 engine Autolite - 3AUT6U1 Minneapolis-Moline All 6-Cyl 2890, 3490, 3496, 4290, 4292, 4293, 4296, 5297 IAD-4040-1 Autolite - 3AUT6U1 Myers All 6-Cyl 6060, 6095 Series (Chrysler 30 engine) Autolite - 3AUT6U1 New Holland All 6-Cyl 800, 810 Forage Harvester (Continental engine) IAD-6002-1G Autolite - 3AUT6U1 Oliver All 6-Cyl 33 (Continental F-226 engine) Autolite - 3AUT6U1 All 6-Cyl Edible Bean, 5542, 5555, (Chrysler engine) Autolite - 3AUT6U1 All 6-Cyl 430, 431, 525, 535, 542, 545 (Chrysler engine) IAD-4040-1 Autolite - 3AUT6U1 Regal And Rockol All 6-Cyl B, C, E, ER, EW, HR, HW IAD series Autolite - 3AUT6U1 www.Hot-Spark.com/Installing-Hot-Spark-Autolite.pdf International Buyers – Please Note: Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. VERY IMPORTANT -- BEFORE ORDERING: Some distributors of vehicles, boats, etc. may differ, according to whether the stock distributor is still in place or a replacement distributor has been installed. Some otherwise similar or identical engines use different distributor brands and/or different distributor part numbers. We need your distributor's brand name, distributor part number and number of engine cylinders to ensure that the electronic ignition conversion kit is correct one for your particular distributor. If your distributor part number, normally found on the side of the distributor body, is not among those listed on the relevant web page, this Hot Spark ignition conversion kit won't fit your distributor. It's imperative that we know your distributor's brand name, distributor part number and the number of cylinders of your engine. You may need to remove the distributor temporarily, so that you can read the distributor part number from the side of the distributor body. Usually, the side of your distributor will be covered with oil and dirt, so you'll need to clean it to find the distributor brand name and exact part number. We can guarantee only that each of our ignition kits will fit a distributor with one of the distributor part numbers listed on its relevant web page. Otherwise, it likely won't fit. HotSpark ignition kits require a 12-volt, negative ground (earth) electrical system. If you order the wrong electronic ignition conversion kit for your distributor, you'll need to return it to us, via US Postal Service mail within 30 days from date of purchase. If the ignition kit is in perfect, unused condition, we can accept it as a retuned item, within 30 days of purchase, and provide a refund to your PayPal account, less a 25% restocking fee and any international shipping fees, etc., but only if the ignition kit is in pristine, unused condition. Buyer is responsible for shipping and other costs to return the product for credit or exchange. 3AUT6U1 Electronic Ignition Conversion Kit for 6-cylinder Autolite/Prestolite Distributors Easy to Install - Replace Points, Condenser and Entire Breaker Plate with Solid-State Electronics for 6-cylinder, non-vacuum-advance Autolite/Prestolite distributors with two vertical screws securing breaker plate to distributor body Electronic Ignition Conversion Kit. Replaces points and condenser in many 6-cylinder Prestolite/Autolite centrifugal-advance distributors. Application: 6-cylinder Prestolite/Autolite centrifugal-advance distributors with two vertical screws securing breaker plate to distributor body. Ignition kit replaces entire breaker plate. For 12V negative ground only. For Autolite/Prestolite Distributors: IAD-4005A IAD-4012A IAD-4025 IAD-4025A IAD-4027 IAD-4033 IAD-4033A IAD-4034 IAD-4039-1 IAD-4040-1 IAD-4105-1M IAD-4108-1M IAD-411 4M IAD-4113M IAD-4114 1M IAD-4201 IAD-4201-1 IAD-4203-1 IAD-6001 IAD-6001-1B IAD-6001-2D IAD-6001-2F IAD-6001-2RL IAD-6001C IAD-6001D IAD-6001E IAD-6001G IAD-6002 IAD-6002-1A IAD-6002-1C IAD-6002-1D IAD-6002-1E IAD-6002-1F IAD-6002-1G IAD-6002-1K IAD-6006-1 IAD-6009-2A IAD-6010-1 IAD-SERIES IAO-4101-1M IAO-4103 IAO-4103-1 IAO-4103A IAO-4109-1M IAO-4112M IAO-4113-1M IAO-4113M IAO-4115-1M IAO-4116-1 IGC-4225F IGC-6001 IGC-6001-2D IGC-6001A IGC-6001B IGC-6001C IGC-6001G IGC-SERIES 12V negative ground only. Coil Required: Coil must have 3.0 Ohms or more internal primary resistance. In stock: Available: Item Number: 3AUT6U1 Price: US $79.95 FREE SHIPPING to anywhere in the USA Item Name: Hot-Spark Electronic Ignition Conversion Kit for 6-cylinder Prestolite/Autolite centrifugal-advance Distributors with screw-down breaker plate. Includes everything you need - no external ignition box required. Price: US $79.95 Price with Shipping Shipped within USA $79.95 USD Shipped to Other Countries $119.95 USD BOSCH Black Coil BOSCH Black Coil 3.4 Ω primary resistance 7.4K Ω secondary resistance 3.4 Ohms primary resistance Ideal for Use with Hot-Spark Electronic Ignition Conversion Kits with red 3-series ignition module or for use with breaker points. Heavy-duty coil with 3.3 Ohms primary resistance. Ideal for points or electronic ignition. Produces strong, blue spark at the Application: Ideal for Hot Spark ignition kits or for use with points. Provides plenty of primary resistance to protect from overheating due to high-voltage environments. No external ballast resistor required. Bonus: Includes three ¼" male connectors for each coil terminal. Produces strong, blue spark when used with Hot-Spark red electronic ignition conversion kits (red ignition module). Also excellent for points-based distributors - high primary resistance helps reduce points burning, pitting. Standard 56mm (2.2 in.) coil diameter - fits stock coil clamps. In Stock: Available: Item Number: Bosch Black Coil Price: US $39.95 Shipping: Free Priority shipping to anywhere in the USA Item Name: Bosch Black Coil Price US $39.95 Bosch Black Coil with 3.4 Ohms primary resistance Shipped within USA $39.95 USD Shipped to Other Countries $79.95 USD HS14BR Hot-Spark 1.4 Ω Heavy-Duty Ceramic External Ballast Resistor 1.4 Ohm Ballast Resistor - Ideal for Use with Electronic Ignition and High-Voltage Charging Systems Also reduces burning and pitting of contact breaker points. 1.4 Ω heavy-duty, external ceramic ballast resistor - installed between coil's + terminal and condenser or HotSpark ignition's red wire. Lowers amperage to points or ignition module, ensuring trouble-free operation. Installed on engine firewall or on coil. Ideal for use with high-voltage charging systems and electronic ignition or points. Application: Recommended for use with high-voltage charging systems. Typically lowers current @ 3,000 RPM by about 0.5 amps.Supplements original stock coil. Also extends the life of points when used with points-based ignition systems. Reduces burning and pitting of points. In Stock: Available: Item Number: HS14BR Price: US $15.95 FREE SHIPPING to anywhere within the USA. Ships to USA only - no international shipping available for this item, unless ordered with distributor, coil or ignition kit. Charging system voltage, measured at the coil’s + terminal, must never exceed 13.9 volts, at any RPM level. You can reduce over-amperage surges/voltage spikes to the ignition module by wiring a 1.4 Ohm ballast resistor between the coil's + terminal and the red Hot Spark ignition module's red wire. Price with Shipping Shipped within USA $15.95 USD Foreign Orders: Shipping discount available if purchasing multiple items. Dealer Inquiries welcomed. © 2005-2021 Hot Spark® 1561 91561

Price: 79.95 USD

Location: Austin, Texas

End Time: 2024-01-28T03:29:23.000Z

Shipping Cost: 0 USD