Bora-Care with Mold-Care 1 Gallon- NOT FOR SALE TO: NY

Description: Not For Sale To: NEW YORK ( due to regulations )Nisus Bora-Care with Mold-Care - 1 gallon ( 128 oz. ) Bora-Care with Mold-Care active: Disodium Octaborate Tetrahydrate (Borate) 40% MOLD-CARE active: Didecyl dimethyl ammonium chloride 80% Bora-Care with Mold-Care will kill existing mold and prevent future mold growth, but it will not remove the black stains caused by mold and fungus. To remove the actual stains from mold and fungus, you should apply Mold-Clean before applying the Bora-Care with Mold-Care. BoraCare with Mold-Care combines BoraCare with Mold Care. It protects the surface, killing all forms of fungi (including mold). As a borate-based wood preservative, Boracare renders treated wood impervious to termites and other wood destroying insects, as well as wood decay fungi. BoraCare with Mold-Care also disinfects and sanitizes the treated areas. When used together, BoraCare with Mold-Care creates a highly effective, residual solution to insects and mold. Boracare with Mold Care penetrates into the wood where it delivers residual protection for years. It is the only EPA-registered product that will not only kill mold and insects, but prevent mold from growing on wood surfaces Inhibits Mold Growth & Stops Wood Destroying Insects-Inside Out Protection Mold Care prevents the growth and establishment of mold, dry rot or wet rot. Mold Care was formulated to work with Bora-Care. Boracare will add protection from wood destroying insects such as Termites, Powderpost Beetles, Anobiid Beetles, Old House Borers and Decay Fungi for years. Application of Bora Care with Mold Care can be used on bare wood, drywall, particleboard or OSB. This product is designed to penetrate wood; it doesn't just remain on the surface. It will penetrate and absorb into the interior of the wood for inside out protection. Ways to use Boracare with Mold Care 1. New Construction When a home is being built, all wood is accessible. This is the perfect time to do a whole house Bora-Care with Mold-Care treatment. This whole house treatment protects all wood from mold, termites, carpenter ants and wood boring beetles, and even discourages general pests such as cockroaches. Bora-Care with Mold-Care diffuses into the wood and remains in the wood, delivering residual power for years of protection. 2. Water Damaged Materials If there has been damage from water such as rain, flood waters or leaking pipes, apply Boracare with Mold Care to the affected wood after the damaged wood has been cleaned and dried. After cleaning, wood decay or mold can begin to grow at once. If you apply Mold Care, you can stop the wood decay immediately as you kill the existing mold. In the advent of future flooding, you are protecting the wood, as well. Besides stopping the mold growth, Boracare with Mold Care sanitizes and disinfects damaged wood, creating a buffer zone. 3. Preventative application To prevent high risk areas such as crawl spaces, bathrooms and kitchens, use Boracare with Mold Care as a one time preventative application. It may be applied either in a new construction phase or post construction. BoraCare with Mold-Care Mixing Instructions As a concentrate, Boracare dilutes with water before use. To aid in the mixing process use warm or hot water if available. An impeller-type mixer that can be used with an electric drill will aid the mixing. Mix 1 pint of Mold Care with 1 gallon of Boracare in 5 gallons of water. For mold control, mix 1 pint of MoldCare with 1 gallon of BoraCare in 5 gallons of water following the methods below: A. Hand Sprayers: Mix in a separate clean container such as a 5 gallon bucket, then pour mixed solution into a spray tank. You can cause blocked hoses and nozzles, by mixing directly in the sprayer tank. B. Hand Volume Pumping Systems: Add all the water to the tank, first then start recirculator. Add BoraCare and Moldcare Concentrate slowly. Continue mixing until it is uniform.This mixed solution will remain stable for up to 30 days. Cautions: Remove pressure from spray tanks before leaving unused solution overnight. After using Boracare with Moldcare, flush or clean lines and equipment. For use: in an around buildings and structures for listed pests.Residential, institutional, public, commerical, agricultural and industrial Yield - Treats approx. 3600 lineal feet of 2x4 dimensional lumber. Please see label for complete application directions and yield amounts. Mixture|Application - Mix mix entire contents of Bora-care with Mold-care with five gallons of hot or warm water. Notes for Powderpost Beetles and Boracare Application Powderpost Beetles may have adults emerging from treated wood up to a year, due to their life cycles. If the wood is too dry (less than 15%), depth of penetration with the Boracare may only occur to the top 1/4 inch. To solve this, spray the wood first with water to increase moisture. Bora-Care with Mold-Care is the pest control industry's leading product in the fight against mold. It is the only EPA-registered product that will both kill and prevent mold on wood surfaces. Not only does Bora-Care with Mold-Care treat mold, but it also acts as a surface protectant, killing all forms of fungi, sanitizing and disinfecting the treated area. In addition, wood treated with Bora-Care with Mold-Care will render wood impervious to termites, powderpost beetles and othe wood-destroying insects. Bora-Care with Mold-Care can be applied as a one-time preventative application during the new construction phase of a home, or applied post-contruction to high-risk areas such as kitchens, bathrooms and crawl spaces. Bora-Care with Mold-Care will remain in treated wood forever, providing years of residual protection. Great for homes in flood zones. Can be applied to bare wood, plywood, particleboard, oriented strand board (OSB). NOTE: Bora-Care with Mold-Care may come in a blue or green jug. It is the same product just different container colors. How Bora-Care with Mold-Care Works Mold-Care is the industry’s leading weapon against mold. It acts as a surface-protectant, killing all forms of fungi, sanitizing and disinfecting the treated area. Bora-Care is the industry’s leading borate-based wood preservative, rendering treated wood impervious to termites and other wood destroying insects, as well as wood decay fungi. It actually diffuses into the wood where it remains for the life of the wood, providing residual protection. When used together, they create a highly effective solution to insects and mold. Mold-Care is the only EPA-registered product that will both kill and prevent mold. Combined with Bora-Care, it also kills and prevents decay fungi and wood destroying insects that share the same conducive conditions and actually cause much more damage. Mold-Care is a specific quaternary ammonium compound called diecyl dimethyl ammonium chloride (a cationic surfactant). This is negatively charged and has both a hydrophobic and hydrophilic component so that it ruptures mold and bacteria cell membranes. These compounds are actively used in hospitals as well as in the beer and food industries as sanitizers. Use Mold-Care instead of other products which either have no EPA registration and can actually cause fungal decay and structural failure or which can off-gas poisonous components in wall voids and hot attics. Target Pests Brown Rot (including dry rot), White Rot, Wood Decay; Drywood Termites: Kalotermes, Incisitermes; Powderpost Beetles: Lyctinae, Bostrichidae; Anobiid Beetles: Anobiidae; Old House Borers, Longhorned Beetles: Cerambycidae, Hylotrupes ACTIVE INGREDIENTS: Bora-Care: Disodium Octaborate Tetrahydrate (Borate) 40%, Mold-Care: Didecyl dimethyl ammonium chloride 80% Bora-Care with Mold-Care Application Instructions *Always read the product label completely before use. Mixing Procedure: Pour 4 gallons of water into a six-gallon pail. Attach mixing impeller to drill and begin agitation. Gradually add 1 gallon of Bora-Care and 1 pint of Mold-Care Moldicide Concentrate into the pail of water and continue to mix solution. Use 1 gallon of water to triple rinse the Mold-Care Moldicide Concentrate and Bora-Care containers and pour contents into the mixing solution. Continue to mix until solution is fully mixed. Normal mixing time may be 5 minutes. Warm water will reduce mixing time. Mix solution in a container other than spray equipment, then transfer finished solution into spray equipment. Mixed solution is stable for up to 30 days. Do not leave unused solution under pressure or in tank overnight. Clean and/or flush equipment and lines with water after use. *Assure uniform coverage of surfaces to be treated. Surfaces must be evenly wet without runoff or pooling. Permit treated surfaces to be thoroughly dry before painting or affixing overlayment materials such as siding, wallboard or flooring. The entire contents of the Bora-Care with Mold-Care concentrates yields 6 gallons total of finished solution. This treats approximately 3600 lineal feet of 2x4 lumber or 1250 sq. ft. of a crawl space or attic. See label and Application Rates Tables for treatment amounts for other dimensional lumber and panels, siding, and plywood. Standard Application Dilution Rates / Mixing Ratios for Bora-Care with Mold-Care: *Mix entire contents with 5 gallons of warm water (see mixing instructions above). *One gallon of finished solution treats 400 board feet of wood or 400 sq. ft. of sheathing, insulation, or drywall. Bora-Care with Mold-Care is for use in the following areas: In and around Residential, Industrial, and Commercial Structures including Homes, Apartments, Garages, Museums, Public and Private Institutions, Schools, Hotels, Hospitals, Kennels, Stables, Farm Buildings, Trucks, Trailers, Warehouses and Non-Food Areas of Supermarkets, Restaurants and Food Processing Plants Surfaces: for use on all non-food contact surface cellulosic materials including wood, plywood, particle board, paper, oriented strand board (OSB), cardboard (non-food packaging material), wood composite structural components, concrete, block, brick, metals, PVC plumbing pipes and other non-cellulosic materials where an intact water-repellent barrier, such as paint, stain or sealer, is not present Indoors- Preventative Treatment for Drywood Termites, Wood Boring Beetles and Fungi (Rot): Apply when access to wooden structural components is optimized such as at the “dried-in” stage when sheathing and roofing are in place, yet before installation of insulation, wiring, plumbing and other mechanical components. Concentrate application in areas susceptible to attack, to include all sills, plates, floor joists, piers, girders and subfloors. See product label for full details. In areas where access is limited to 1 or 2 sides of a wood member including exterior wall base plates and any married studs, apply 2 coats of solution to the exposed surfaces. Allow first application to dry by waiting at least 20 minutes between applications. Preventative Treatment for Drywood Termites and Powderpost Beetles: Apply 1 coat of solution to the point of surface saturation to all structural wood surfaces using a brush, spray or mist. Apply 2 coats of solution to those surfaces where access is limited to 1 or 2 sides of structural wood members. Allow first application to dry by waiting at least 20 minutes between applications. Outdoors- Bora-Care with Mold-Care should only be used on exterior wood that is then sealed. DO NOT use to directly treat soil. Bora-Care solution provides only limited and temporary protection of wood in contact with the ground (see specific instructions) and is not a substitute for products registered for protection of wood in contact with the ground. Treatment of Exterior Wood Surfaces Less Than Two Inches Thick such as Decks, Sheds and Fences: Apply only to bare wood or to wood surfaces where an intact water repellent or finish is not present. Remove paint or finish prior to application. Apply 1 coat of solution to the point of surface saturation to all wood surfaces. Apply 2 coats of solution to heavily infested areas and to those surfaces where access is limited to 1 or 2 sides of wood members. Allow first application to dry by waiting at least 20 minutes between applications. Do not apply in rain or snow. Do not expose treated exterior wood surfaces to rain or snow for at least 48 hours after treatment. If inclement weather is expected, protect exterior treated surfaces with a plastic tarp. For longer performance, exterior wood surfaces that have been treated will require a topcoating with a water-resistant finish such as paint or exterior stain. Apply the finish or topcoat within 6 weeks of treatment. It is important to allow treated wood to completely dry (at least 48 hours) before applying any protective topcoat. Bora-Care with Mold-Care Features Treats whole house or high-risk areas A Bora-Care with Mold-Care treatment is a one-time preventative application that can be completed either during the new construction phase or applied post-construction in high-risk areas such as kitchens, bathrooms and crawl spaces. Provides residual protection Bora-Care with Mold-Care diffuses into wood and remains there for as long as the wood is in service, providing years of residual protection. Creates a buffer zone In an untreated home, flood damage can cause mold to grow within a week. The mold can be as devastating as the flood itself. Even in catastrophic conditions, Mold-Care will act as a retardant to mold growth, giving the homeowner more time to recover. It also disinfects and sanitizes, critical necessities in a water-damage situation. Inhibits the growth of mold Specifically designed to work with Bora-Care, Mold Care prevents the establishment of dry rot, wet rot and mold. Bora-Care adds additional residual protection against decay fungi and insect infestation. Bora-Care with Mold-Care can be applied to bare wood, plywood, particleboard, and oriented strand board (OSB). And it’s the best approach you can take against mold. Bora-Care with Mold-Care is designed to penetrate wood; it doesn’t just remain on the surface, but is absorbed into the interior of wood to protect it from the inside out. Extra Tips *Clean surfaces with Mold-Clean before treatment to eliminate mold and fungus stains. *Bora-Care with Mold-Care will not treat active infestations of wood-destroying insects because the dilution rate of the finished solution is 5:1 rather than 1:1. *Only dilute with warm water. *Always pre-mix in a separate container before filling spray equipment. *Use only on raw wood materials. Bora-Care products will not penetrate paint, stain, or sealants (though these products may be applied after Boracare applications are dry). *An appropriate dye or colorant such as Turf Mark Blue Tablets may be added to the solution when diluting Bora-Care with water to make it easier to see where Bora-Care has been applied. *Do not use or store near heat or open flame. *Do not apply with foggers or similar equipment. *Not labeled to be tank mixed with other products. Storm and Water Damage Steps STEP 1: Remove all wet and unsalvageable building material from the site. STEP 2: Completely dry the remaining affected areas. STEP 3: Spray Bora-Care with Mold-Care according to the label application directions on all structural wood and cellulosic building materials, including sheet rock. Allow to dry before rebuilding. Bora-Care with Mold-Care - the perfect solution to water damage when mold is present. The active ingredient in Mold-Care kills existing mold on wood and inhibits mold from growing. Bora-Care with Mold-Care gives wet wood a chance to dry out safely. Applying Bora-Care with Mold-Care to a water damaged home will kill existing mold and prevent mold from reoccuring. Remember, nothing can stop mold from growing if the conducive conditions are not corrected. Protecting Structures From Moisture and Fungi After Flooding Steps STEP 1: Wear appropriate protective gear and make sure the electricity and HVAC are off. STEP 2: Begin removing mud, flooded furniture, appliances, carpets, and flooring. STEP 3: Clean thoroughly and disinfect with an appropriate EPA registered disinfectant, sanitizer and virucide like Nisus DSV. STEP 4: Cut out sheet rock 2 feet above the highest water line to allow for proper drying. STEP 5: Open doors and windows to begin circulating fresh air. Use fans and dehumidifiers if available. STEP 6: Use a moisture meter to determine when wood is 19% or less moisture content. STEP 7: Treat all exposed wood using Bora-Care with Mold-Care in a 5:1 Solution. STEP 8: Apply termite protection with a 2 foot band treatment using Bora-Care in a 1:1 solution. Once dry, the home is ready for repair. Please note: BORA-CARE is also sold alone, without the Mold-Care additive (if you do not need mold control). Bora-Care with Mold-Care will not eliminate existing termites, powder post beetles, or other wood destroying organisms because it is mixed at a 5:1 ratio to eliminate mold and you need to mix normal Bora-Care at a 1:1 ratio to eliminate existing wood eating insects. Please read the label for more instructions. CAN NOT SELL OR SHIP THIS PRODUCT TO: NY It is a violation of Federal law to use this product in a manner inconsistent with its labeling. I will follow all applicable federal and state laws and regulations regarding the sale of this product I won't accept bids from, sell to, or ship to states in which the item is not registered as a general-use product No oral advice or written information given by us shall create a warranty. We are a seller of various products. We do not warranty the safety or the effectiveness of any of the products listed on this site. Any warranty or guarantee of safety or purpose for any particular use lies solely with the manufacturer. Products always have a label attached and it is here by noted that for all purposes the label is the law and according to federal law the product label must be followed and that any product must be used according to the label directions. Any advice or recommendations given by us or anyone representing us will never be intended to take the place of the product label.The label is the law and a legal document. Always read and follow the label directions before using any product. Some of the products sold by us could require special licensing training or registration of the user in that users State, County, City, Etc. It is the sole responsibility of the purchaser and/or the end user to provide a license, permit, registration etc. If required by that purchasers local or state authorities.It is the sole responsibility of the user to verify that any products purchased are licensed for use in their State, County or City. The customer assumes all responsibility for safe, proper and legal use of any products they purchase. The products we sell are intended for personal use only, in accordance with the customer's state laws and restrictions.

Price: 145.95 USD

Location: Atlanta, Georgia

End Time: 2024-01-25T03:11:10.000Z

Shipping Cost: 0 USD