850mm Frame with APM2.8 M8N GPS 350KV Motor 2-6S 40A ESC UFO ZD850 DIY Drone Kit

Description: ZD850 DIY Drone Kit 850mm Full Carbon Fiber Umbrella Airframe with APM2.8 Flight Control M8N GPS 350KV Motor 2-6S 40A ESC Quadcopter UFO Drone Note : Product is DIY Version, Unassembled Kit and NO Manual, Please take it into account before ordering. Our technicist will help client to weld the some wiring for ESC and we will test all electronic parts before shipment. If any Technical questions, Please message us Note: The item do not include Battery! Recommend 3-6S less than 10000mah Lipo battery Product Listing : ZD850 Full Carbon Fiber Frame Kit with Unflodable Landing Gear Foldable Arm *1 350KV Brushless Disk Motor high Thrust With Mount *6 2-6S 40A ESC*6 Suitbale for APM2.8 2.6 2.5 2.52 and PIXHAWK Power Module*1 Power electronic converter integrated circuit *1 Three-hole High Quality Carbon Fiber1555 CW CCW Propellers *3 Pairs APM2.8 APM 2.8 No Compass Flight Controller Board Bent Pin with Case *1 Mini M8N GPS Module NEO-M8N GPS *1 10cm Servo Receiver Extension Lead Wire Cable M/M *1 CNC GPS Anti-interference Antenna Mount Holder Stent Case *1 4X Hook & Loop Fastening Tape *1 1m Black and Red 16AWG Silicon Wire Connecting Wire * 1 15.XT60 Male with 14AWG Wire 10cm *1 3D Robotics 3DR Radio 433MHz Telemetry Kit *1(Optional) Flysky 2.4G 9ch FS FS-TH9X Transmitter & Receiver Combo*1 (Optional) Precautions: 1 Do not charge the battery when you are away from home, do not charge the battery immediately after flying, do not over-discharge the battery (over-discharge may cause the battery to fail to charge and become useless). . 2. Do not modify any parameters and wiring without knowing the flight control and remote control. 3. Turn on the remote control before powering on the airplane, unplug the power switch after the flight, and then close the remote control to prevent accidents. 4. This aircraft is recommended to fly indoors. It can fly in an open place outdoors when there is no wind, and avoid flying in crowds and places with disturbing objects around. 5. The product is unassembled/welded in loose parts. If you have any technical and assembly questions, please feel free to contact us. We have a dedicated technical team to answer related questions. If customers need to assemble, please feel free to contact us, we will give a reasonable quotation for additional logistics freight and technical assembly fees. 6. This product is not a toy and is not suitable for children under 14 years of age. 7. Please read the instructions carefully before any use. If you are a beginner, it is recommended to be assisted by an experienced adult 8. Because the airplane is relatively small, don’t fly high and far. 9. Novices should pay attention not to use the airplane when the airplane is turning or let children take it to prevent it from being scratched. 10. Please turn off the start switch in time when the aircraft falls from a wall or hits other objects during flight, otherwise it may cause damage to the flight control motor, etc. Check whether the aircraft is damaged or the screws are loose. Functions and features: 850mm wheelbase arm foldable frame Maximum load: 3.5KG under 6S battery Can be used for aerial photography and aerial survey With data transmission, it can plan flight routes Paddle: Specification: 1555 Material: carbon fiber Length: 15 inches Spacing 5.5 Main hole 4mm Side hole 3mm Center distance 12mm ESC: Current: 40A Peak current (10 seconds): 60A BEC: None Battery LiPo: 2-6S Programmable elements: synchronization (high/medium) Weight: 26g Size: 68 * 25 * 8.7 Motor: Size: 5010 KV: 350 KV Shaft diameter: 4 mm Weight: about 105 grams Applicable voltage: 2-6S Flight control: APM2.8 APM 2.8 No compass Flight Control Features: - Arduino Compatible! - Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally - Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer - Onboard 4 MegaByte Dataflash chip for automatic datalogging - Optional off-board GPS, uBlox LEA-6H module with Compass. - One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000. - Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties. - Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively. 1. data transmission port 2. analog sensor port 3. autostability gimbal output 4. ATMEGA2560 SPI online programming port (be useful for optical flow sensor) 5. USB port 6. remote control input 7. function selection jumper 8. GPS port 9. 12C external compass port 10. ATMEGA32U2 SPI online programming port 11. multifunction configurable MUX port (OSD is the defaulted output) 12. current voltage port 13. ESC power supply selection jumper 14. ESC output port 3DR Telemetry Kit: - Very small size - Light weight (under 4 grams without antenna) - 433 MHz - Receiver sensitivity to -121 dBm - Transmit power up to 2

Price: 454.7 USD

Location: Shenzhen

End Time: 2024-11-20T09:32:13.000Z

Shipping Cost: 25 USD