Description: 3M VHB（Very High Bond）Tape 3M VHB Tapes provide the convenience and simplicity of a tape fastener and are ideal for use in many interior and exterior bonding applications.In many situations,they can replace rivets, spot welds,liquid adhesives and permanent fasteners.5952 This family matches the modified acrylic adhesive on both sides of very conformable foam, providing adhesion to the broadest range of substrates, including most powder coated paints. 1.Application Ideas Bonds to a variety of plastics and paint systems 2.Relative Adhesion HSE： High LSE： Med Relative Adhesion: HSE – High Surface Energy LSE – Low Surface Energy 3.Temperature Resistance Minutes Hours： 300°F(149°C) Days Weeks： 250°F(121°C) 4.Solvent Resistance: High 5.Thickness w/o liner :45 mils(1.1mm) 6.Adhesive Type: Modified Acrylic 7.Foam Type: Very Conformable 8.Liner Type: D Liner Types: A – 3 mil 54# Densified Kraft Paper B – 5 mil Clear Polyethylene Film C – 2 mil Polyester Film D – 5 mil Red Polyethylene Film E – 4 mil 58# Polycoated Kraft Paper Please read the following text and try to understand before use!!!Application Techniques 1.Clean Most substrates are best prepared by cleaning with a 50:50 mixture of isopropyl alcohol (IPA*) and water prior to applying 3M™ VHB™ Tapes. Exceptions to the general procedure that may require additional surface preparation include: • Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or grease from a surface and should be followed by cleaning with IPA/water. • Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt or oxidation and can increase surface area to improve adhesion. • Adhesion Promoters: Priming a surface can significantly improve initial and ultimate adhesion to many materials such as plastics and paints. • Porous surfaces: Most porous and fibered materials such as wood, particleboard, concrete, etc. need to be sealed to provide a unified surface. • Unique Materials: Special surface preparation may be needed for glass and glass-like materials, copper and copper containing metals, and plastics or rubber that contain components that migrate (e.g. plasticizers). Refer to 3M Technical Bulletin “Surface Preparation for 3M™ VHB™ Tape Applications” for additional details and suggestions. (70-0704-8701-5) *Note: These cleaner solutions contain greater than 250 g/l of volatile organic compounds (VOC). Please consult your local Air Quality Regulations to be sure the cleaner is compliant. When using solvents, be sure to follow the manufacturer’s precautions and directions for use when handling such materials.2.Pressure Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure develops better adhesive contact and helps improve bond strength. Typically, good surface contact can be attained by applying enough pressure to insure that the tape experiences approximately 15 psi (100 kPa) pressure. Either roller or platen pressure can be used. Note that rigid surfaces may require 2 or 3 times that much pressure to make the tape experience 15 psi.3.Temperature Ideal application temperature range is 70°F to 100°F (21°C to 38°C). Pressure sensitive adhesives use viscous flow to achieve substrate contact area. Minimum suggested application temperatures: • 50°F (10°C): 3M™ VHB™ Tapes 4950, 5952, 4910, 4952, 4611, 4622 families. • 60°F (15°C): 3M™ VHB™ Tapes 4941, 4945 families. • 32°F (0°C): 3M™ VHB™ Tape 4951 families. Note: Initial tape application to surfaces at temperatures below these suggested minimums is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory. To obtain good performance with all 3M™ VHB™ Tapes, it is important to ensure that the surfaces are dry and free of condensed moisture.4.Time After application, the bond strength will increase as the adhesive flows onto the surface (also referred to as “wet out”). At room temperature approximately 50% of ultimate bond strength will be achieved after 20 minutes, 90% after 24 hours and 100% after 72 hours. This flow is faster at higher temperatures and slower at lower temperatures. Ultimate bond strength can be achieved more quickly (and in some cases bond strength can be increased) by exposure of the bond to elevated temperatures (e.g. 150°F [66°C] for 1 hour). This can provide better adhesive wetout onto the substrates. Abrasion of the surfaces or the use of primers/ adhesion promoters can also have the effect of increasing bond strength and achieving ultimate bond strength more quickly.
Price: 6.99 USD
Location: Suzhou, Jiangsu
End Time: 2023-09-03T10:15:08.000Z
Shipping Cost: 3 USD
Product Images
Item Specifics
Return shipping will be paid by: Seller
All returns accepted: Returns Accepted
Item must be returned within: 60 Days
Refund will be given as: Money Back
Return policy details:
Country/Region of Manufacture: United States
MPN: Does Not Apply
Brand: 3M
Fast Fulfillment: YES
Model: 5952
Type: Double Sided Foam Tape
Available Variations
Color: 5mm
Price: 6.99 USD
Available Quantity: 399
Quantity Sold: 399
Color: 8mm
Price: 7.99 USD
Available Quantity: 214
Quantity Sold: 214
Color: 10mm
Price: 9.99 USD
Available Quantity: 543
Quantity Sold: 523
Color: 1/4"
Price: 6.99 USD
Available Quantity: 163
Quantity Sold: 146
Color: 1/2"
Price: 12.99 USD
Available Quantity: 355
Quantity Sold: 333
Color: 3/4"
Price: 16.99 USD
Available Quantity: 211
Quantity Sold: 208
Color: 1"
Price: 19.99 USD
Available Quantity: 316
Quantity Sold: 316
