1:5 1/5 Scale Rovan 29cc Gas Gasoline Baja Remote Control HPI 5B Blue

Description: 1:5 1/5 Scale Rovan 29cc 2 Stroke Gas Baja Remote Control Car HPI 5B (READ!) Hello, I live in Ohio. I love these cars for their speed, size and durability. I want your experience to be good as mine has been. To keep prices low we can only ship FREE via FedEx Ground or FedEx Home Delivery.These are the new 2024 High Strength Grade A Models, Not factory seconds, grade B, or older models.5B Specifications:Engine: 29cc single-cylinder, air-cooled two-stroke.Maximum Speed: 40MPH+ in stock configuration.Remote Control: 2.4GHz, 6-channel. Tested at distances over 600 feet without issues. Requires 4 AA batteries (not included).Battery: Built-in SC6V, 2000mAh battery for extended run time. Steering Gear: All-metal gear throttle steering gear and metal gear steering gear with a plastic case.Exhaust System: High-quality tuned exhaust pipe. Loud operation; mufflers are available if needed.Width Side to Side: Rear wheel 15 3/4, Front 15 1/2.Wheel Base: 22 3/8 Inch.Overall Size: 32 1/8 Long x 18 7/8 Wide x 10" High.Weight: 34lbs.Upgraded: Second-generation wasteland tires on second-generation wheel hubs.Upgraded: 8,000rpm ClutchUpgraded: Second generation reinforced front and rear suspension with 6mm Shocks.Upgraded: 997 Carburetor replaces Walbro and fits 23 to 32cc Zenoah, CY, HPI BAJA, RV KM 5B 5T 5SC Assembly and Operation:Out of the Box: Ready to race once the wheels are installed and the car battery has been charged. Minimum 2 hours charge recommended.Battery Charging: The car features a charging plug and comes with a USB charger. No disassembly required for charging. Allow battery to cool down for 30 minutes after full charge before operation. Remove charger within 30 minutes of full charge (green light) to prolong battery life. Store battery fully charged. (we use a count down timer like item 386419780550 on ours.) Crash Durability: Minor crashes are unlikely to cause significant damage. Personal experience with a 20MPH crash into a tree resulted in less than $20 in repairs.Fuel Mixing: Uses a 25:1 gasoline-to-oil ratio. Fill the small compartment of the mixing jug to the 25:1 line with oil, then fill the gas compartment to the 25:1 line. We’ve had great results with Evinrude Johnson Outboard Premium 2-Stroke Engine Oil (purchased in 1-gallon jugs), which minimizes carbon buildup and avoids plug fouling. Many other brands can also be used.Radio: This 6 channel radio essentially only uses 2 channels with this car. Trim is on the 4 adjustments under the cover on the back of the radio. Top left - steering trim. Top right - throttle & brake trim, Bottom left - control extents. Starting Instructions:Ensure the car and radio are powered on and responding.Set the choke on the right side of the car (red lever on the carburetor) to the vertical closed position.Press the primer bulb on top of the carburetor 3 to 4 times, or once fuel is visible.Gently pull the starter rope until it engages, then pull swiftly. Do not pull the rope out completely; use short quick pulls.Crank until the engine fires (usually 1 to 3 pulls).Turn off the choke, then pull the rope 1 or 2 times to start the engine.Break-In Process:Initial Run: Start by running the car at idle to 1/4 throttle or less for about 5 minutes. Let the engine cool down completely after this run.Second Run: Repeat the same process less for 10 minutes, then allow it to cool down.Third Run: You can start pushing it a little harder, but keep in mind that a new engine generates more heat due to increased friction. Run for 8 to 10 minutes, then let it cool.Subsequent Runs: Continue the process for about five runs, being mindful of any debris that could block cooling. A clean engine runs cooler.Final Break-In: After these runs, you can run the car at full throttle and let it burn through an entire tank of fuel.Post-Break-In: Be sure to check and snug up the exhaust pipe after the initial break-in process.Before each run check bolts throughout the car to ensure they are tight. Lock-tight is recommended on clutch and brake assembly bolts. clean bolts and holes with alcohol and a q-tip to ensure lock-tight adhesion. You will be tempted to upgrade some of the parts to aluminum. But let me tell you, aluminum is unforgiving, breaks and destroys everything behind it. The High Strength ABS Plastic will give and bounce back without damage. Many plastic components are way better. Warning: These cars are not suggested for small children and can cause serious burns from the exhaust and engine. Be mindful of observers, children and animals, as they can sustain severe injury or death if impacted by the car.

Price: 549 USD

Location: Hillsboro, Ohio

End Time: 2024-11-08T00:39:11.000Z

Shipping Cost: N/A USD